DC Power Supply

with analogue and digital control, USB, RS232, LAN (LXI) and GPIB

• Versatile solution for direct testing of dc power sources and PFCs
• Constant current, resistance, conductance and power modes
• Wide voltage and current range, 10 to 500V and 0 to 16A
• 400 watts continuous dissipation at 28°C (360W at 40°C)
• High resolution and accuracy for level setting
• Built-in transient generator with variable slew
• Current monitor output for waveform viewing
• Variable drop-out voltage for battery testing
• High resolution backlit graphic LCD with soft key control
• Analogue remote control of levels and TTL control of on/off and transient switching
• Front and rear input terminals
• Load inputs rated to CAT II (300V)
• Full bus control via USB, RS232, GPIB and LXI compliant LAN interfaces

with analogue and digital control, USB, RS232, LAN (LXI) and GPIB

• Versatile solution for direct testing of dc power sources and PFCs
• Constant current, resistance, conductance and power modes
• Wide voltage and current range, 10 to 500V and 0 to 16A
• 400 watts continuous dissipation at 28°C (360W at 40°C)
• High resolution and accuracy for level setting
• Built-in transient generator with variable slew
• Current monitor output for waveform viewing
• Variable drop-out voltage for battery testing
• High resolution backlit graphic LCD with soft key control
• Analogue remote control of levels and TTL control of on/off and transient switching
• Front and rear input terminals
• Load inputs rated to CAT II (300V)
• Full bus control via USB, RS232, GPIB and LXI compliant LAN interfaces

• Multiple ranges on each output for wider voltage/current choice
• Four independent 105W full performance outputs
• Instant individual on/off control plus sequencable multi on/off
• Simultaneous display of meters and settings for all outputs
• Up to 250 settings memories for individual or multiple outputs
• Instant access to voltage/current setting for any output
• USB, RS-232, LXI compliant LAN, and GPIB* interfaces (P versions)
• USB, RS-232, LXI compliant LAN, and GPIB* interfaces (P versions)
  Duplicate power and sense terminals at rear (P versions)

• Proven member of a modular Power Module family, more than 800 units are in service
• Precision-regulated Bi-Polar output provides up to +12 to -12 Amps for Magnet loads.
• Smooth operation through zero amps output current, no “Crossover” problems.
• All 2510 MCOR12 Power Modules are identical and interchangeable.
• Has two high-precision measurements of output current;
  • one is used to close the regulation control loop,
  • provides an independent monitoring signal to the Crate Interface Card.
• Fault sensing circuitry in the module sets a Fault Latch which inhibits the output.
• A (momentary) Sync input signal inhibits MOSFET switching when it is active (high);
  • this eliminate switching noise .
  • reduces power line noise during sensitive analog signal measurements.

• Proven member of a modular Power Module family, more than 800 units are in service
• Precision-regulated Bi-Polar output provides up to +30 to -30 Amps for Magnet loads.
• Smooth operation through zero amps output current, no “Crossover” problems.
• All 2510R30 MCOR30 Power Modules are identical and interchangeable
  • Programming Card is plugged into the replacement module.
• Each channel has a critically-damped, LC noise filter with a cut-off frequency of about 8 kHz.
• A 16-pin front panel diagnostics connector taps onto major circuit nodes which enables quick “inthe-crate” fault evaluation

Enabling single-contact high-current/high-voltage test

• Enables coaxial measurements up to 10,000 V and 300 A pulsed (600 A in a parallel configuration) with a single touchdown
• Even distribution of high current with innovative multi-fingertip design
• Compatible with Tesla 200/300 mm power device characterization system
• Reduced measurement time by testing both high-voltage and high-current conditions with a single touchdown
• Accurate characterization of a wide range of pad sizes and test currents, with minimum pad damage and contact resistance
• Safe, reliable and repeatable high-current/voltage measurements over a wide temperature range (from -55°C to +300°C)

AC, DC, AC+DC, Single and Three – Phase -Models Including Cabinets

Rated Power 60,000 (vA),  Output Power 21,000(w)  Output form  1,2,3Ø, Output Volt-Max 300(L-N)/425 (VAC/VDC)(1), Output AMPS/PHS 166.7 / 83.3 (AAC/ADC)(2), Input Power Form (3) 3 Ø, Panel Height (4) 27 (U) and Weight 527/240 (LBS./KG).

AC, DC, AC+DC, Single and Three – Phase -Models Including Cabinets

Rated Power 30,000 (vA),  Output Power 21,000(w)  Output form  1,2,3Ø, Output Volt-Max 300(L-N)/425 (VAC/VDC)(1), Output AMPS/PHS 125.0 / 62.5  (AAC/ADC)(2), Input Power Form (3) 3 Ø, Panel Height (4) 27 (U) and Weight 466/212 (LBS./KG).

AC, DC, AC+DC, Single and Three – Phase -Models Including Cabinets

Rated Power 30,000 (vA),  Output Power 21,000(w)  Output form  1,2,3Ø, Output Volt-Max 300(L-N)/425 (VAC/VDC)(1), Output AMPS/PHS 25.0/13.9 (AAC/ADC)(2), Input Power Form (3) 3 Ø, Panel Height (4) 15 (U) and Weight 320/146(LBS./KG).

AC, DC, AC+DC, Single and Three – Phase -Models without Cabinets

Rated Power  12000 (vA),  Outputform  1,2,3Ø, Output Volt-Max 300(L-N)/425 (VAC/VDC)(1), Output AMPS/PHS  33.3/16.7 (AAC/ADC)(2), Input Power Form (3) 3 Ø, Panel Height (4) 4 (U) and Weight 112/51 (LBS./KG).

Photovoltaic applications, the quality and technical data of the AC-DC converter is of primary interest. Solar installations are intended for a lifetime of roughly 20 years, therefore even fractions of a percent in efficiency will represent significant amounts of energy losses.

Programmable Grid-tie Sink High-Power DC Supply,